Metal-roof PV in high-wind regions; conceptual engineering rendering.

A solar clamp pull-out test report answers a specific question about the assembly that was tested. Using its result on a roof requires checking the profile, material, installation details, loading direction and test boundaries, and then checking how the force reaches the building structure.

In cyclone regions, the distinction between a clamp test and a roof-system test is particularly important. A high static pull-off result does not establish the cyclic resistance of the roof assembly, and a tested roof does not automatically qualify an added solar attachment.

Conceptual illustration of a solar array attached to a metal roof, introducing profile fit, connection testing and the complete load path.

Concept illustration. The attachment geometry and arrangement are not a product specification or an installation detail.

Start with the attachment forces, not a clamp count

The required arrangement comes from the relationship between wind actions, rail behaviour, attachment resistance and the roof beneath it.

Determine the net wind action on the PV array for its geometry, clearance, location and applicable design standard. Roof-cladding pressure and the net pressure across a raised module are different quantities; one should not be substituted for the other without justification. Resolve the resulting attachment forces into the directions covered by the clamp test. Tilted modules may introduce a combination of roof-normal and in-plane forces.

Next, analyse the module attachment positions and rails to obtain reactions at the roof clamps. Check those reactions against appropriate design resistances, then check the sheet, concealed clips, fasteners and supporting structure. Adding clamps changes force distribution; it does not automatically remedy an inadequate roof connection.

Profile fit: cover width is not rib pitch

Cover width is the effective width contributed by an installed sheet. Rib pitch is the distance between adjacent ribs. A multi-rib sheet can have several rib intervals within one cover width.

Lysaght lists nominal cover widths of 406 mm and 700 mm for its corresponding KLIP-LOK profiles. These dimensions must not be treated as the spacing between every adjacent rib. Obtain the actual rib centres, rib-head shape and eligible clamp positions from the drawing for the roof being installed. Lysaght profile information.

Conceptual metal-roof cross-sections showing full sheet cover width separately from the spacing between adjacent ribs.

Figure 1. Cover width and rib pitch describe different dimensions. The sections are schematic; they do not establish any manufacturer's dimensions, clamp compatibility or permitted attachment spacing.

Record these details before choosing an attachment:

Roof detailWhat to establish
Profile and manufacturerExact designation, roll-former and current profile drawing
Rib geometryRib centres, head width, undercut and engagement surfaces
Sheet materialBase metal thickness, alloy or steel grade, coating and condition
Roof attachmentConcealed clip or screw detail, support spacing and support material
Clamp installationCorrect clamp model, orientation, fasteners and specified torque
Permitted locationsAny restrictions relative to clips, supports, laps or sheet ends

An offcut helps confirm geometric fit. It cannot establish structural capacity. Roofs with similar names or appearance may have different rib shapes, materials or fixing systems.

Lysaght's standard KLIP-LOK brochures identify their non-cyclonic scope and direct cyclonic applications to separate guidance. Establish the approved roof specification before transferring any clamp result to it. KLIP-LOK 406 guide, KLIP-LOK 700 Hi-Strength guide.

Follow the load from the module to the purlin

A clamp converts part of the load collected by a rail into a concentrated action on the roof. The complete path may include the clamp, rib, sheet, concealed clips, clip screws and purlins.

Conceptual load path from PV modules and rails through a seam clamp, roof sheet, concealed fixing and purlin.

Figure 2. Components in a typical concealed-fix roof load path. Arrows identify the path conceptually; actual force distribution between clips and supports requires analysis or representative testing. A clamp test may cover only part of this assembly.

Check the links separately:

  • Clamp and rib: pull-off, sliding, jaw opening, local deformation and any combined loading.
  • Roof sheet: the effect of concentrated attachment loads, including their positions between supports. A distributed-pressure capacity table is not a direct point-load rating.
  • Concealed clips and fasteners: sheet engagement, clip resistance, fastener resistance and the distribution of reactions from all relevant rails.
  • Purlins and their connections: the additional PV actions together with the applicable roof and building loads.

The roof still carries its own wind action. The roof designer must consider this together with PV reactions under the relevant load combinations. A single clamp reaction is not necessarily the total demand on a roof rib, clip or purlin.

Thermal movement also belongs in this review. Check the roof sheets, fixed points, sliding clips, rails and expansion joints as one assembly. Movement available at the roof clips does not guarantee that an added PV rail arrangement will remain compatible.

Read a pull-out report as evidence with boundaries

Matching the specimen to the roof is necessary, but it is not sufficient. A useful report makes the test arrangement and the derivation of its reported resistance clear.

Report itemWhy it matters
Clamp identificationA result belongs to the tested model and configuration
Profile, material and thicknessGeometry and material properties affect the connection response
Loading directionRoof-normal pull-off, seam-parallel sliding and lateral loading are different cases
Fixture and support conditionsA restrained sheet coupon may behave differently from an installed roof span
Clips and fasteners includedDefines whether the roof attachments were actually part of the tested path
Torque and installation procedureIdentifies the installation condition associated with the result
Load-displacement behaviour and failure modeDistinguishes slip, deformation, disengagement and component failure
Specimen count and individual resultsAllows assessment of variation rather than reliance on the best result
Resistance basisIdentifies ultimate test load, characteristic resistance, allowable load or limit-state design resistance
Cyclic evidence, where requiredEstablishes what repeated loading was applied and how acceptance was assessed

Sample size affects statistical treatment, but does not alone determine the characteristic resistance. The measured results, their variation and the selected assessment method also matter.

Keep the action and resistance formats consistent. Compare ultimate limit-state actions with the appropriate limit-state design resistance. Compare allowable-stress-design actions with a resistance derived for that basis. Do not treat a maximum laboratory load as an allowable or design load, or apply a second factor to a value already reduced without understanding its derivation.

For a related discussion of profile dependence, see why a standing-seam clamp's pull-off capacity depends on the roof profile. Comparative results illustrate the issue; project selection still requires the relevant test evidence.

Static, cyclic and site tests answer different questions

Three test categories compared: a static clamp pull test, a cyclic roof-system pressure test and a controlled site proof test.

Figure 3. Test boundaries matter as much as the applied load. Schematics are explanatory, not test procedures. A roof-pressure sequence cannot be converted into a clamp-force qualification without defining the specimen, force conversion and acceptance criteria.

A static clamp test measures the response of a particular connection and fixture under its prescribed loading. Roof-system pressure testing includes a different assembly and loading distribution. Site proof testing checks selected installed connections against a defined acceptance procedure; it does not establish their ultimate capacity or substitute for cyclic qualification.

NCC 2022 Volume One, Specification 4 provides a useful documented example. Its Low-High-Low roof-cladding sequence uses 4,500, 600, 80, 1, 80, 600 and 4,500 cycles, with peaks of 0.45, 0.6, 0.8, 1.0, 0.8, 0.6 and 0.45 times the reference pressure, Pt. The total is 10,361 cycles. The peak cycle is held for at least 10 seconds, and cycling is below 3 Hz. Pt incorporates the prescribed ultimate wind pressure and variability allowance. These provisions concern the roof assembly within the specification’s scope. They do not themselves certify a solar clamp. Confirm the code edition and jurisdictional provisions applicable to the project. NCC 2022 Specification 4.

Where cyclic evidence is needed for a clamp-on-roof connection, the engineer must define the representative assembly, loading directions, loading history and acceptance criteria. Simply reproducing a pressure sequence as a force sequence is not enough.

Worked example: what rail spacing changes

The following is a beam calculation illustration, not a roof specification, product rating or recommended clamp layout. All numerical inputs are assumed.

  • Modules are parallel to the roof. Net design uplift normal to that plane is 3.0 kPa.
  • The assumed rail tributary width is 1.139 m, giving a uniformly distributed line load of 3.417 kN/m.
  • The rail is idealised as four equal continuous spans of constant stiffness, with simple end supports, no overhang and the same uniform loading on every span.
  • Available attachment positions permit the assumed support spacings of 0.70 m or 1.40 m. These are attachment spacings, not the rib pitch of a named roof product.
  • The assumed clamp design resistance is 4.0 kN in the corresponding roof-normal direction. This is an illustrative design value, not a Solaracks rating.

For this particular beam model, the largest interior reaction is 8/7 × w × s, approximately 1.143ws. The end reaction is 11/28 × w × s, approximately 0.393ws, where w is the line load and s is the span.

Assumed spacingLargest interior reactionComparison with assumed 4.0 kN resistance
1.40 m5.47 kNExceeds the assumed resistance
0.70 m2.73 kNBelow the assumed resistance for this single check

At 0.70 m spacing, the model's end reaction is 0.94 kN. These coefficients were derived for the stated idealisation. Actual module clamps introduce discrete loads, rail joints may interrupt continuity, and overhangs or changes in wind pressure can alter the governing reaction.

The lower reaction does not establish that the assembly is adequate. Rail strength and deflection, all attachment actions, the roof load path and applicable cyclic requirements remain to be checked. Combine the relevant reactions when evaluating shared roof components.

Count attachments from the completed layout. A four-span rail has five support locations; a long-row estimate based only on module width divided by support spacing omits end effects and should not be presented as this model's clamp count per module.

Make site checks specific and controlled

Installation quality needs a documented procedure covering the correct clamp model, seating, fasteners, torque and inspection records. Do not transfer the torque for a module clamp bolt to a roof clamp or set screw merely because the nominal thread size is the same.

If site proof testing is specified, the engineer should define the sample locations, loading direction, fixture reaction points, proof load, displacement limits and post-test acceptance criteria. Being below a design resistance does not itself guarantee that a test will leave the sheet undamaged.

A local pull-test fixture may react against nearby sheet metal without verifying the concealed clips or purlins. The procedure must state which parts it evaluates. Record the applied load, movement and observed condition, and investigate a failed test before authorising repair, re-tightening or further testing.

Check corrosion compatibility without assuming a universal coating rule

Review the materials at every contact point, including clamp bodies, screw tips, washers, roof coatings and isolation components. An attachment's overall material description does not show which parts actually touch the roof.

Use guidance for the specific roof product and environment. An isolation detail must preserve the verified mechanical engagement and remain suitable over the intended service life; an improvised pad can change both fit and load transfer.

ISO 9223 classifies atmospheric corrosivity. It does not, by itself, prescribe a universal anodising thickness for a solar clamp in each category. Select surface treatment using the product specification, exposure, durability requirements and relevant material guidance. ISO 9223 scope.

A practical engineering selection sequence

  1. Identify the exact roof profile, material, fixing system and supporting structure.
  2. Confirm clamp fit and permitted attachment positions from product drawings and representative specimens.
  3. Determine PV wind actions and resolve them into the attachment's loading directions.
  4. Analyse the actual module and rail arrangement, including joints, ends, overhangs and pressure zones.
  5. Check each governing reaction against appropriately derived resistance and interaction criteria.
  6. Verify the complete roof load path, thermal movement and corrosion compatibility.
  7. Confirm the required cyclic evidence and applicable project standards.
  8. Issue the installation and inspection requirements for the selected configuration.

For a Solaracks enquiry, include the roof profile drawing, sheet specification, clip and purlin information, array layout and project design criteria. Request the current product-specific drawing, material specification, installation instructions and relevant test report. Availability, packing and delivery terms belong in the project quotation.

Be Supported.

Related reading

Frequently asked questions

How many standing-seam clamps per module are needed in a cyclone region?

There is no universal count. The layout must satisfy the PV design actions, rail reactions, verified attachment resistance and roof-system checks. Count the actual attachments in that layout, including end supports.

Does a 700 mm cover width mean ribs are 700 mm apart?

No. A multi-rib sheet can contain several rib intervals within its cover width. Use the exact profile drawing to establish rib centres and eligible clamp positions.

Can a Klip-Lok 406 clamp test be used for Klip-Lok 700?

Not automatically. The proposed assembly must be covered by relevant evidence for its geometry, material, installation and loading conditions. A similar product name or appearance is not evidence of equivalent resistance.

Does passing Low-High-Low testing certify the solar clamp?

Only the defined specimen and scope have been evaluated. Roof-cladding qualification does not automatically cover an added PV connection, and a separate clamp test does not automatically qualify the roof beneath it.

Which pull-out value should be used in design?

Use a resistance with a documented derivation and a basis consistent with the design actions. Establish whether the reported number is a maximum test load, characteristic resistance, allowable load or limit-state design resistance before using it.

Can a site proof test establish the clamp's cyclone rating?

No. A controlled proof test checks selected installed assemblies at the specified test level. It does not replace ultimate-capacity assessment or representative cyclic testing.

Do seam clamps suit trapezoidal or IBR roofs?

Do not transfer a standing-seam detail solely on appearance. Use an attachment verified for the exact profile and support arrangement, with the roof manufacturer's acceptance. The suitable solution may be a dedicated clamp or a bracket with an appropriate fastening and sealing detail.

Is a thicker anodised finish enough for a coastal roof?

Coating thickness is only part of durability. Material compatibility, coating quality, exposure, water retention, contact details and maintenance also matter. Specify the complete detail for the project environment.

Get an engineered mounting quote for your project.

Share drawings, module layout, site location, wind load, snow load and corrosion environment. Solaracks will recommend the system, material, layout and packing approach.

Request a quote